The crankshaft turns the up-and-down motion of the pistons into rotation, and it runs on a thin film of oil inside its bearings. When that oil film breaks down — through contaminated oil, low oil pressure, overheating or simply long running hours — the journals wear, score or go out of round. Crankshaft grinding restores those surfaces so the engine can be rebuilt with new bearings instead of an expensive new crankshaft.
At Global Prime Engineering in Sharjah Industrial Area 2, crankshaft grinding is part of our in-house engine rebuilding service. We regrind crankshafts from cars, pickups, trucks, buses, heavy equipment, generators and marine engines for customers across Sharjah, Dubai and the Northern Emirates.

Warning signs of a worn crankshaft
- A deep knocking from the bottom of the engine, especially under load
- Low oil pressure, or the oil warning light flickering at idle
- Bearings that come out scored, discoloured or worn through to the backing
- Metal particles in the oil or oil filter
- Vibration that persists after other causes have been ruled out
- A spun bearing or a seized engine
Stop early, save more
If you notice these symptoms, stop the engine as soon as it is safe to do so. Running a damaged bottom end can turn a simple regrind into a scrapped crankshaft and a damaged block.
How crankshaft grinding works
Grinding removes a small, precisely controlled amount of material from the main journals and the connecting-rod (crankpin) journals so that they are round, straight and smooth again. Because the journals become slightly smaller, the engine is then assembled with matching undersize bearings — commonly 0.25 mm, 0.50 mm, 0.75 mm or 1.00 mm undersize (0.010, 0.020, 0.030 or 0.040 in).
The aim is to remove only as much material as needed to clean up the damage. That keeps the crankshaft strong and leaves room for a future regrind.
Our crankshaft reconditioning process
- 1
Cleaning and inspection
The crankshaft is cleaned and inspected for cracks, heat damage and scoring, and the oil passages are checked.
- 2
Measurement
Every journal is measured for size, ovality and taper, and the shaft is checked for straightness (run-out).
- 3
Straightening where possible
A bent crankshaft is corrected before grinding when the damage allows it.
- 4
Precision grinding
Main and crankpin journals are ground on our dedicated crankshaft grinding machine to the correct undersize, keeping the proper fillet radii at the journal edges.
- 5
Polishing and finishing
Journals are polished to a smooth finish and the oil holes are deburred so that the new bearings bed in correctly.
- 6
Dynamic balancing
Recommended for high-speed and heavy-duty engines: the crankshaft can be balanced on our dynamic balancing machine to reduce vibration and bearing load.
- 7
Final check
The finished journal sizes are recorded so that you order the correct undersize bearings.
Regrind, repair or replace?
Most crankshafts can be reground at least once — many several times — before they reach the last available bearing undersize. Replacement is usually the better choice when the crankshaft is cracked, when the journals are already at their final undersize, or when heat damage from a seized bearing has gone too deep.
Once the crankshaft has been inspected and measured, we tell you honestly which option makes economic sense.
Engines we work on
- Passenger cars, 4x4s and pickups
- Trucks, buses and fleet vehicles
- Construction and earth-moving equipment
- Diesel generators and compressors
- Marine engines for workboats and vessels
- Industrial engines in plants and pumping stations
Why garages and fleet operators choose us
A reground crankshaft is only as good as the rest of the rebuild. Because we also bore, hone and face cylinder blocks, face cylinder heads, cut valve seats, pressure-test heads and bore connecting-rod bushes in-house, your engine machining stays under one roof — with one team accountable for the result.
- Dedicated crankshaft grinding and dynamic balancing machines
- Complete engine machine-shop services in one workshop
- ISO 9001 certified quality management
- Industrial Area 2, Sharjah — easy to reach from Dubai and Ajman
Frequently asked questions
How much does crankshaft grinding cost in Sharjah?
The price depends on the engine, the number of journals, the amount of damage and whether straightening or balancing is needed. We quote after inspecting the crankshaft — send photos on WhatsApp for an initial idea.
How long does crankshaft grinding take?
It depends on the crankshaft’s size and condition and on our current workload. We give you a realistic timeline with the quotation, and we prioritise breakdowns where we can.
Do I need new bearings after grinding?
Yes. Grinding reduces the journal diameter, so the engine must be assembled with matching undersize main and connecting-rod bearings. We give you the exact undersize after grinding.
Can a cracked crankshaft be repaired?
A cracked crankshaft is generally not safe to put back into service and should be replaced. We check for cracks during inspection and advise you before any grinding is done.
Do you grind crankshafts for trucks, generators and marine engines?
Yes. As well as car and pickup engines, we work on crankshafts from trucks, buses, construction equipment, generators, compressors and marine engines.